+86 192 7034 8382
A qualified supplier should provide a model-specific technical data sheet listing VLT, IR rejection, UV rejection, thickness, warranty, test method, and revision date. I use these fields to compare window tint film without relying only on brochure language or installer claims. The figures should identify the tested glass configuration, measurement wavelength, laboratory method, and product model. If a supplier provides only a general catalog, I request a separate TDS for each film series and shade before approving a purchase.
For installers, distributors, vehicle manufacturers, and commercial building contractors, a window film TDS is a purchasing document rather than a promotional summary. It connects the selected model with measurable performance, physical construction, installation conditions, and warranty obligations. Astrum presents automotive, architectural, nano-ceramic, carbon, sputtering, metallized, and other film categories, making model-level comparison especially important when selecting a product for a specific market.
!
When I review a window film technical data sheet, I look for five core performance fields: visible light transmission, infrared rejection, ultraviolet rejection, total solar energy rejection, and physical thickness. I also check the film material, adhesive type, layer construction, color, recommended glass, testing standard, and warranty period. A document is more useful when every value is connected to a model number rather than presented as a range for an entire product family.
The revision date and document identifier matter because suppliers may change coatings, adhesive systems, colors, or warranty conditions without changing the broad product name. I also ask whether the values were measured on bare glass, laminated glass, or a complete glass-and-film assembly. That distinction can materially affect the result reported to the buyer.
I found model-level values published across several Astrum automotive film product pages. The table below normalizes the available data into one comparison format. Astrum publishes VLT, IR cut, UV cut, thickness, and warranty for many models, while TSER is explicitly listed for the chameleon series; for models without a published TSER value, I would request the supplier’s complete TDS before using the figure in a bid or performance guarantee.
| Film family | Model | Thickness | VLT | IR rejection or IR cut | UV rejection or UV cut | TSER | Warranty |
|---|---|---|---|---|---|---|---|
| Nano ceramic | AC-0590 | 2 mil | 4% | 95% | 99% | Request TDS | 5 years |
| Nano ceramic | AC-1590 | 2 mil | 15% | 90% | 99% | Request TDS | 5 years |
| Nano ceramic | AC-3590 | 2 mil | 35% | 90% | 99% | Request TDS | 5 years |
| Nano ceramic | AC-7090 | 2 mil | 72% | 80% | 99% | Request TDS | 5 years |
| Nano ceramic | AC-03100 | 2 mil | 3% | 98% | 99% | Request TDS | 10 years |
| Nano ceramic | AC-35100 | 2 mil | 35% | 98% | 99% | Request TDS | 10 years |
| Nano ceramic | AC-35100S | 4 mil | 35% | 98% | 99% | Request TDS | 10 years |
| Carbon | C05 | 2 mil | 4% | 61% | 99% | Request TDS | 10 years |
| Carbon | C35 | 2 mil | 38% | 46% | 99% | Request TDS | 10 years |
| Sputtering | A-V70 | 1.8 mil | 71% | 80% | 99% | Request TDS | 10 years |
| Sputtering | A-LX25 | 3 mil | 21% | 93% | 99% | Request TDS | 10 years |
| Chameleon | CM8070 | 2 mil | 81% | 66% | 98% | 54% | 8 years |
| Chameleon | CM6080 | 2 mil | 62% | 93% | 99% | 53% | 8 years |
| Chameleon | CM7592 | 2 mil | 68% | 92% | 99% | 55% | 8 years |
This comparison shows why model-level documentation matters. A 35% VLT nano-ceramic model may have 90% or 98% IR rejection depending on the series, while a 35% carbon model is listed at 46% IR rejection. The shade alone does not identify heat-control performance, and the words “ceramic,” “carbon,” or “sputtering” do not replace a tested specification.
Visible light transmission VLT describes how much visible light passes through the glass and film combination. A lower VLT generally produces a darker appearance and stronger privacy effect, while a higher VLT supports a brighter cabin and may be more suitable for windshields or front side windows subject to local regulations. I never compare the film’s nominal shade alone because factory glass already has its own VLT value.
For example, Astrum lists AC-0590 at 4% VLT, AC-3590 at 35%, and AC-7090 at 72%. These models can create very different visual results even though each belongs to the same nano-ceramic family. The final installed VLT depends on the original glass, so I request a combined-glass calculation or measure a sample assembly before approving a vehicle program.
A TDS should also clarify whether VLT was measured according to a recognized automotive glazing method and whether the result represents the film alone or the film installed on reference glass. This information helps installers check compliance with regional tint laws. It also reduces disputes when a film advertised as “70%” measures differently after installation on factory glass.
Infrared and ultraviolet rejection are not interchangeable measurements. IR rejection refers to the reduction of infrared radiation within a defined wavelength range, while UV rejection refers to ultraviolet transmission, usually across a shorter wavelength band associated with fading and exposure concerns. A supplier may report a high IR figure at one wavelength, but that value does not automatically represent the film’s average performance across the entire infrared spectrum.
When I compare IR claims, I ask for the test wavelength or wavelength range, sensor configuration, glass type, and whether the reported number is IR cut, IR rejection, or infrared energy reduction. A single-wavelength result and a broadband result should not be placed in the same ranking without a clear label. This is one of the most common reasons two apparently similar films show different results in installer demonstrations.
UV figures also require context. Astrum lists 99% UV cut for many nano-ceramic, carbon, and sputtering models, while certain glue film models show lower values such as 81%, 90%, or 93%. I treat the exact wavelength range as essential because “UV rejection” without a defined band can conceal differences in test scope.
Some ceramic films are designed to avoid metallic signal interference with GPS, radio, mobile communications, or toll systems. That should still be confirmed for the specific model and vehicle because antenna placement, coated glass, ADAS hardware, and factory glazing can affect signal behavior. I request a compatibility statement or sample test when the film will be installed on vehicles with antennas or advanced driver-assistance sensors.
TSER measures the portion of solar energy rejected by the complete glass-and-film system. It is often more useful for comparing overall solar control than an isolated IR percentage because solar heat includes visible, infrared, and ultraviolet components. However, TSER depends on the reference glass, glazing thickness, film orientation, and test standard, so values should be compared only when the test conditions match.
Astrum’s chameleon series provides published TSER values ranging from 53% to 58% across the listed models. The same type of value is not shown in the accessible parameter tables for every carbon, nano-ceramic, glue, or sputtering model. Therefore, I would not infer TSER from the IR figure; I would request the missing value and its test conditions directly from the supplier.
Performance also changes with installation quality and glass condition. Dust, edge contamination, trapped moisture, incorrect heat shrinking, poor adhesion, and optical distortion can reduce the practical result even when the film’s laboratory data is valid. A procurement decision should therefore include both the product TDS and an installer qualification requirement.
Film thickness affects handling, forming, durability, and the intended application. Astrum’s published automotive examples range from 1 mil glue film to 4 mil nano-ceramic film, with several carbon and ceramic models listed at 2 mil and sputtering models listed at 1.8 mil or 3 mil. I check whether the stated thickness includes the adhesive and whether the number refers to the finished film or only the PET substrate.
The construction should identify whether the film is dyed, carbon, metalized, sputtered, ceramic, or multi-layer optical film. It should also identify the adhesive type, liner, scratch-resistant coating, and any hard coat used to protect the surface during cleaning. These details affect installation behavior, signal compatibility, color stability, and warranty eligibility.
For automotive installers, a 2 mil film and a 4 mil film may require different shrinking and handling methods. For architectural projects, thickness and layer construction may also affect glass compatibility, thermal stress, safety performance, and edge sealing. I ask the supplier to confirm approved glass types and installation restrictions rather than assuming that one film can be applied to every window.
A warranty statement should do more than list a number of years. It should identify the covered product models, film defects, color change, bubbling, peeling, delamination, adhesive failure, and whether the coverage belongs to the original buyer, installer, distributor, or end customer. It should also state whether professional installation, approved cleaning products, registration, or proof of purchase is required.
Astrum’s published warranty periods vary by family and model. The listed nano-ceramic AC-0590 through AC-7090 models carry 5-year warranties, several higher-series nano-ceramic models carry 10 years, carbon models carry 10 years, sputtering models carry 10 years, chameleon models carry 8 years, and selected glue film models carry 1 or 2 years.
I would not treat a 10-year product warranty as a 10-year installation warranty unless the written document says so. Warranty coverage may exclude damage from abrasive cleaning, ammonia-based products, improper installation, glass replacement, accidents, severe environmental exposure, or unauthorized modification. The installer should receive the current warranty document before the purchase order is issued.
Astrum provides product-level performance tables and offers technical data sheets or catalogs for its automotive and architectural film ranges. The publicly displayed tables are useful for initial screening because they identify model codes, VLT, IR cut, UV cut, thickness, and warranty for multiple families. However, a complete procurement TDS should also include test methods, TSER where applicable, construction details, adhesive information, revision control, and formal warranty terms.
My direct answer is: Astrum appears able to supply technical documentation, but buyers should request a separate, current, downloadable TDS for every selected model rather than treating a product webpage or catalog as the final technical record. I would also ask the supplier to confirm whether the document is controlled by revision number and whether the supplied production batch matches the tested sample. This distinction separates a preliminary product listing from a procurement-ready technical package.
Before comparing quotations, I use the following checklist for each model and shade:
A window film technical data sheet should be the primary document I use before comparing performance, installation suitability, and warranty coverage. It should identify VLT, IR rejection, UV rejection, TSER, thickness, material, adhesive, construction, testing conditions, manufacturer identity, and warranty terms for each individual model. Astrum publishes useful model-level values across nano-ceramic, carbon, sputtering, chameleon, glue, and other film families, but buyers should request the complete current TDS when TSER, test methods, construction, or warranty exclusions are not shown.
The most practical next step is to send the supplier a model-by-model request containing the exact fields in the checklist above. I would then validate a sample on the target glass, compare the TDS revision with the production batch, and confirm the written warranty before placing an order. This process provides a more reliable basis for selecting nano ceramic car window tint film or another window film category than comparing marketing claims alone.
Related Products
Tailored PPF & Window Film To Fit Your Market Needs
Backed by strong R&D and advanced facilities, Astrum delivers flexible customized film solutions for global partners.